BDH Engineering

Max Swing Over Bed Covers 530mm. Max Swing Over Carriage 330mm. Max Diameter Turned 300mm. Traverses:- X = 240 mm. Z = 600 mm. S/No T30017 - 1998

Table 835mm x 360mm. Traverses X = 490mm Y = 340mm Z = 480mm. Spindle Nose 40BT. ATC Capacity 16 Tools. S/No 25280 - 1996.

Table 835mm x 420mm. Traverses X = 580mm. Y = 410mm. Z = 480mm. Spindle Nose 40BT. ATC Capacity 22 Tools. S/No 35171 - 1994

Max Swing Over Bed 280mm. Max Swing Over Cross Slide 150mm. Traverses:- X = 300 mm. Z = 360 mm. Turret with 8 Stations. S/No 16512 - 1987

Table 860mm x 315mm. Spindle Nose 30 Int Quick Change. S/No 642670585

With Metric Dials. Swing over Bed 390mm Dia x 1270mm B.C. Swing in Gap 580mm. Swing over Cross Slide 240mm. S/No 6/0044/32469DD

Table 1500mm x 280mm. With Power Feeds to Table Long & Cross Travel. Spindle Nose 40 Int with Power Quill Feeds. Note: Longitudinal & Vertical Feed Motors on Knee Require Attention.

Table 1066mm x 228mm (42" x 9"). Spindle Nose R8. Spindle Speeds to 3750 RPM. With Swivelling Milling Attachment & Power Table Feed. S/No 338750780V

Table 1244mm x 305mm. Spindle Nose 50 Int. With Arbor & 2 off Arbor Supports. Spindle Speeds 26 to 405PRP. S/No EGH213.

Table 762mm x 205mm. With Power Long Feeds. Spindle Nose 40 Int. Speeds to 2500 RPM. With 2 off Arbor Supports & Change Gears. S/No1ESJ 5501A0270

Table 889mm x 393mm. Two Spindles 3 Morse Taper with Power Feeds. Speeds (8) 84 to 2940RPM. One Spindle 2 Morse Taper Hand Feed. Speeds (4) 470 to 2940RPM. S/No 23371A

S/No 6X3499H

S/No L1659E1A

S/No E1588

Note: Incomplete - Requires Attention. Inspection Recommended. S/No D2080E1A

Includes: Castings, Bar Feeds, Pulleys, Collets, Pump Parts, Tool Posts, Slides, Bearings etc. See Additional Documents for a PDF List.

Manual Pull Down Feed. Blade 275mm Diameter. With Coolant. S/No 385

240 Volt - Single Phase. Throat Approx 300mm. Table 380mm x 380mm. S/No 01324 - 1995

Capacity 304mm x 152mm (12" x 6") Table Area Approx 330mm x 108mm. With Tooling & Equipment. S/No 11042

240 Volt - Single Phase. Spindle Speeds 3000 to 10,000RPM. Table Approx 177mm Diameter. Throat Approx 139mm. S/No M10266

Suitable for Lots 2 & 3

Max Pressure 150 PSI. S/No CO26367

Two Speeds 1400 & 2800RPM. (0.55 & 0.8 kw). S/No 6261314

Max Speed 3000RPM. Max Wheel Size 200mm x 25mm x 20mm Wide

Power 0.33HP. Wheels Approx 140mm Dia x 10mm Wide. Note: Bench Not Included.

Throat Approx 254mm. Max Height Under Slides 228mm. S/No 3D-086 Note: Bench Not Included.

Approx Diameters - 3 Jaws:- 100mm 127mm & 165mm. 4 Jaw: 75mm

Micrometer Sizes: 0-1", 4"-5", 6"-9" & 9"-10"